Leakage testing for different adhesive systems and composites to permanent teeth

Basit Öğe Kaydı
dc.contributor.authorBolgul, B. S.
dc.contributor.authorAyna, B.
dc.contributor.authorSimsek, I.
dc.contributor.authorCelenk, S.
dc.contributor.authorSeker, O.
dc.contributor.authorKilinc, G.
dc.date.accessioned2024-04-24T17:24:13Z
dc.date.available2024-04-24T17:24:13Z
dc.date.issued2017
dc.departmentDicle Üniversitesien_US
dc.description.abstractAim: To explore the microleakage of different adhesive systems and flowable composites to permanent teeth. Subjects and Methods: In this study, a total of 84 human premolar teeth were used. Class V cavities were prepared on the buccal surfaces. The teeth were randomly assigned to six groups of 14 teeth each as follows: The first group u etch-rinse adhesive applied and cavities filled with flowable composite, the second group u etch-rinse adhesive applied and cavities filled with bulk-fill resin composite, the third group u one-stage self-etch (SE) adhesive applied and cavities filled with flowable composite, the fourth group u one-stage SE adhesive applied and cavities filled with bulk-fill resin composite, the fifth group u two-stage SE adhesive applied and cavities filled with flowable composite, and the sixth group u two-stage SE adhesive applied and cavities filled with bulk-fill resin composite. All specimens were then stored for 24 h at 37 degrees C in distilled water. Teeth were then thermocycled for 500 cycles between 5 degrees C and 55 degrees C prior to immersion in 0.5% basic fuchsin for 24 h. Two mesiodistal cuts of each tooth were photographed for leakage with a digital camera. The dye infiltrated surface for each specimen was measured and data were collected with a software program. Statistical evaluations were done by nonparametric KruskaluWallis test and MannuWhitney U-test. Results: There were statistically significant differences in mean microleakage ratio among the groups (P < 0.05). The first group had shown significantly increased microleakage areas than the other four groups (third, fourth, fifth, and sixth groups) (P < 0.05), except for the second group (P 0.05). It was also no significant different between the mean microleakage areas of group fourth and group fifth (P 0.05). The sixth group had exhibited the lowest microleakage areas, and it was statistically significant (P < 0.05) compared to the other groups. Conclusion: In this study, it has been found that the use of total etch adhesive systems resulted in high leakage values.en_US
dc.identifier.doi10.4103/1119-3077.171417
dc.identifier.endpage791en_US
dc.identifier.issn1119-3077
dc.identifier.issue7en_US
dc.identifier.pmid28791970
dc.identifier.scopus2-s2.0-85027693876
dc.identifier.scopusqualityQ2
dc.identifier.startpage787en_US
dc.identifier.urihttps://doi.org/10.4103/1119-3077.171417
dc.identifier.urihttps://hdl.handle.net/11468/19538
dc.identifier.volume20en_US
dc.identifier.wosWOS:000407814700002
dc.identifier.wosqualityQ4
dc.indekslendigikaynakWeb of Science
dc.indekslendigikaynakScopus
dc.indekslendigikaynakPubMed
dc.language.isoenen_US
dc.publisherWolters Kluwer Medknow Publicationsen_US
dc.relation.ispartofNigerian Journal of Clinical Practice
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectAdhesivesen_US
dc.subjectCompositeen_US
dc.subjectEvaluationen_US
dc.subjectLeakageen_US
dc.titleLeakage testing for different adhesive systems and composites to permanent teethen_US
dc.titleLeakage testing for different adhesive systems and composites to permanent teeth
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
PubMed İndeksli Yayın Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu