MILLING PARAMETERS' INFLUENCE ON MACHINABILITY IN MILLING OF CFRP COMPOSITES FUNCTIONALIZED WITH G AND GO

Basit Öğe Kaydı
dc.contributor.authorKilickap, Erol
dc.contributor.authorCelik, Yahya Hisman
dc.contributor.authorDavim, Joao Paulo
dc.date.accessioned2024-04-24T17:12:03Z
dc.date.available2024-04-24T17:12:03Z
dc.date.issued2023
dc.departmentDicle Üniversitesien_US
dc.description.abstractThe use of carbon fiber-reinforced polymer (CFRP) composites having low weight and high strength provides the substantial energy savings in space and aerospace industry. The disadvantage of these composites is that the carbon fiber is not firmly bonded to the epoxy resin and the toughness of the produced materials is low. Graphene (G) and Graphene Oxide (GO) nanoparticles are used to functionalize CFRP composites. The CFRP composites functionalized with G and GO improve the strength of these composites by improving the fiber/matrix interface bond. In this study, the effect of type of nanoparticles, feed rate, cutting speed and number of flutes on machinability (cutting force, delamination factor and surface roughness) were experimentally investigated in the milling of CFRP composites, G-CFRP (CFRP functionalized with G) and GO-CFRP (CFRP functionalized with GO) nanocomposites. Cutting force, delamination factor, and surface roughness were found to be strongly impacted by feed rate, cutting speed, number of flutes, and type of nanoparticles. The increase in the number of flutes contributed to decrease of cutting force, delamination factor and surface roughness, while the increase in the feed rate caused to increase of them. By increasing cutting speed, surface roughness reduced, delamination factor and cutting force increased. In addition, compared to the CFRP composite, the cutting forces and surface roughness were higher, and delamination factor was lower in the CFRP composites functionalized with G and GO.en_US
dc.identifier.doi10.1142/S0218625X23500762
dc.identifier.issn0218-625X
dc.identifier.issn1793-6667
dc.identifier.issue11en_US
dc.identifier.scopus2-s2.0-85171835271en_US
dc.identifier.scopusqualityN/Aen_US
dc.identifier.urihttps://doi.org/10.1142/S0218625X23500762
dc.identifier.urihttps://hdl.handle.net/11468/17833
dc.identifier.volume30en_US
dc.identifier.wosWOS:001044143700002en_US
dc.identifier.wosqualityN/Aen_US
dc.indekslendigikaynakWeb of Science
dc.indekslendigikaynakScopus
dc.language.isoenen_US
dc.publisherWorld Scientific Publ Co Pte Ltden_US
dc.relation.ispartofSurface Review and Lettersen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectCfrpen_US
dc.subjectGrapheneen_US
dc.subjectGraphene Oxideen_US
dc.subjectNanocompositesen_US
dc.subjectMillingen_US
dc.titleMILLING PARAMETERS' INFLUENCE ON MACHINABILITY IN MILLING OF CFRP COMPOSITES FUNCTIONALIZED WITH G AND GOen_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu