Investigation of cutting parameters affecting on tool wear and surface roughness in dry turning of Ti-6Al-4V using CVD and PVD coated tools

Basit Öğe Kaydı
dc.contributor.authorCelik, Yahya Hisman
dc.contributor.authorKilickap, Erol
dc.contributor.authorGuney, Musa
dc.date.accessioned2024-04-24T16:10:39Z
dc.date.available2024-04-24T16:10:39Z
dc.date.issued2017
dc.departmentDicle Üniversitesien_US
dc.description.abstractThere are some problems in the machining of titanium alloys with excellent properties such as high strength, good corrosion resistance, long service life and low weight. The leading problem appears to be the fast tool wear and the bad machining surface. Therefore, in this study, it was investigated whether cutting parameters have effect on tool wear and surface roughness by turning under dry cutting condition of Ti-6Al-4V alloy with excellent properties. CVD (TiCN + Al2O3 + TiN) and PVD (TiAlN) coated WC tools were used in the experiments. Then the Ti-6Al-4V alloy turned with the combinations of the different cutting speed, feed rate, cutting long and depth of cut. We observed that the tools wear in both CVD and PVD coated WC tools increased with increasing the cutting speed, feed rate, depth of cut and cutting length. However, while tools wear increased with increasing cutting speed, the surface roughness reduced to an optimum level. Especially, the surface roughness was worsened above the optimum level changing with increasing the feed rate, cutting length and depth of cut. The tool wear with PVD coated WC tools was observed to be less than the CVD coated WC tools. However, the values of the surface roughness obtained with PVD coated WC tools with increase in depth of cut, feed rate and cutting length has given us higher values when compared to CVD coated WC tools.en_US
dc.description.sponsorshipBatman University by Batman University Scientific Research Projects Unit (BTUBAP) [2015-4]en_US
dc.description.sponsorshipThe authors would like to thank Batman University for financial support given by Batman University Scientific Research Projects Unit (BTUBAP) Project Number 2015-4.en_US
dc.identifier.doi10.1007/s40430-016-0607-6
dc.identifier.endpage2093en_US
dc.identifier.issn1678-5878
dc.identifier.issn1806-3691
dc.identifier.issue6en_US
dc.identifier.scopus2-s2.0-85019195446
dc.identifier.scopusqualityQ2
dc.identifier.startpage2085en_US
dc.identifier.urihttps://doi.org/10.1007/s40430-016-0607-6
dc.identifier.urihttps://hdl.handle.net/11468/14993
dc.identifier.volume39en_US
dc.identifier.wosWOS:000401635900019
dc.identifier.wosqualityQ3
dc.indekslendigikaynakWeb of Science
dc.indekslendigikaynakScopus
dc.language.isoenen_US
dc.publisherSpringer Heidelbergen_US
dc.relation.ispartofJournal of The Brazilian Society of Mechanical Sciences and Engineering
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.subjectWearen_US
dc.subjectRoughnessen_US
dc.subjectTurningen_US
dc.subjectTitaniumen_US
dc.titleInvestigation of cutting parameters affecting on tool wear and surface roughness in dry turning of Ti-6Al-4V using CVD and PVD coated toolsen_US
dc.titleInvestigation of cutting parameters affecting on tool wear and surface roughness in dry turning of Ti-6Al-4V using CVD and PVD coated tools
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu